The programming procedures for flashing an ESP82xx and ESP32 via the serial port differ slightly. Wondershare mobilego 8.5 (full crack mega.
The one download tool supports all of Espressif’s chips (ESP8266 and variants as well). It would probably be a good idea to select the flash size manually rather than just rely on the automatic size detection. The tools are downloaded and installed into a directory specified during ESP-IDF Tools Installer process. By default, this is C: Users username.espressif. Add ESP-IDF tools to PATH using an export script ¶ ESP-IDF tools installer creates a Start menu shortcut for “ESP-IDF Command Prompt”.
The ESP32 Flash Download Tool, just like the ESP8266 download tool, is the official Espressif Download tool that runs on Windows platform. The tool can be used to modify and generate init BINs, generate consolidated BIN files or program multiple chips for production runs. Mar 03, 2017 I read through both the routes of programming an ESP8266 through an Arduino way and as well as the Espressif way using Flash download tools. In an example in SDK 2.0, which describes how to flash a program in ESP8266 using the Flash download tools, they mention that I need to flash the following bin files at specific locations: Non OTA firmware Map. Espressif Systems developed a small software just for this purpose. It is called the ESP Flash Download Tool. In order to download the ESP8266 Firmware Flash Download Tool, visit thislink and in the Tools section, download the ESP Flash Download Tools or you can directly download from thislink.
In general the steps are the same to enter flashing mode on both types ESP boards:
Boot the node with GPIO-0 connected to GND
Start the flashing procedure
Most boards which already have an USB to serial on board, also have some circuit present to help booting into flash mode via the USB port.Such a circuit consists of 2 transistors and a few resistors to trigger the reset and GPIO-0 pin in the correct sequence.All flashing software is able to use this way of bootstrapping.
Some flashing tools also support different methods and thus require a parameter indicating the specific method to boot into flash mode.For ESP boards with an USB to serial adapter on board, the needed boot method is referred to as “NodeMCU” or some abbreviation of this name.
Espressif Flash Download Tool Youtube
Flashing Software¶
A number of flashing tools is included in the nightly build ZIP files.The included tools are all for Windows.
ESP.Easy.Flasher.exeA flasher with graphic UI written by Grovkillen. This tool can also be used to send a number of commands to prepare the unit while still connected to the PC. For example to configure WiFi.esptool.exeA command line ESP8266/ESP32 build and upload helper tool, maintained by Ivan GrokhotkovFlashESP8266.exeA very simple flash tool “ESPEasy Flasher” for ESP82xx. Should be called from the same directory as the compiled bin files:C:DownloadESPEasybin>.FlashESP8266.exeEspressifFlashDownloadToollocated in the directoryEspressif_flash_download_tool_v3.8.5. New versions can be found Espressif Download
For Linux or Mac users, the recommended tool for ESP82xx/ESP32 is esptool.py Harmonics in astrology pdf.
Flashing Parameters¶
Some flash tools allow to set specific parameters, like flash chip related settings.Those parameters are also defined in the compiled .bin files, but when set in the flash tool they are overridden for the boot sequence.As soon as the ESPEasy code is executed, the configured parameters at compile time will be used. Adobe illustrator 2020 mac crack reddit.
N.B. Not all parameters can be set in all flashing tools.
See the documentation of the flash tool for more information.
Baud Rate¶
Most flashing tools allow to set the communication speed.It is advised to use a baud rate of 115200 bps as this seems to be the best trade off between flashing speed and success rate.However it is possible to select a higher baud rate, which may reduce flashing time significantly.
Boards using a FTDI USB to serial chip seem to work fine when flashing at rates of upto 921600 bps.When they fail, it is often presented as a timeout. Try again with flashing at a lower baud rate.
Boards using a CH340 USB to serial chip are less likely to handle high baud rates without errors.
Crystal¶
On ESP8266, the tool will overwrite the 48th byte of RF parameter(default_init_data.bin) if chosen.This option will do nothing for ESP32 chips.
SPI Speed¶
This is the SPI clock speed to read/write SPI flash. (40Mhz default)
Usually 40Mhz is enough and safe, if you want to enable 80Mhz for SPI flash, makesure:
The flash you are using support 80Mhz.
Your PCB layout is good enough for 80Mhz.
The configure byte is in the 4th byte from flash address 0x0. So the tool will overwritethe 4th byte of bin file which is to be written to 0x0 address.
SPI Mode¶
Espressif Flash Download Tool
This sets the SPI data mode for flash R/W operations.
From fastest to slowest mode:
QIO/QOUT: use /HOLD and /WP pin as SPI data2/data3, make sure your flashsupport Quad instructions before select.QIO and QOUT are almost the same. “QIO” will send address in quad mode, where “QOUT” will not.
DIO/DOUT: Use Dual mode instructions to read/write flash.DIO and DOUT are almost the same. “DIO” will send address in Dual mode, where “DOUT” will not.
Almost all flash chips used on ESP32 support DIO/DOUT mode.
Almost all ESPEasy builds are set to use “DOUT” mode.
ESP82xx¶
ESPEasy builds based on esp8266/Arduino library version 2.7.x and later can handle compressed .bin.gz files.When in doubt, just use the .bin files.
ESP32¶
Flashing ESP32 nodes is slightly more complex compared to ESP82xx.
The main differences:
The binary layout on the flash is split in several parts each with their own specific offset from the start of the flash block.
ESP32 allows to have several fuses set (flags which can be set only once)
Most tutorials show the Espressif Download Tool with a number of separate binaries each with their own offset.This is rather error prone, and therefore the ESPEasy build process creates 2 different .bin files.
A binary with
factoryin the file name, used for flashing via serial.A binary without
factoryin the file name, used for flashing via the web interface.
The factory bin file has all separate binaries with their offsets included in a single file.Therefore the needed offset for this factory bin file should be set to 0. (starting at the begin of the flash area)
When the ESP board later needs to update the firmware to a different version, there is no need for a serial connection.This can be done “OTA” (over the air) via the web interface.For OTA updates, use the bin file withoutfactory in the file name.
